[Skyeye-developer] [ SkyEye Release ] Skyeye v1.21 is released.

[kang shuo]

You need to unselect some options on "make menuconfig" of blackfin
uclinux. You can use R0504_linux_config file in the attachement as
your kernel config file .
Use R0504_user_config file in the attachment as your user application
config file.

-- Thanks
-- Michael.Kang

On 2/12/07, andy wang <ypwangreg at gmail.com> wrote:
> Hi, Kang
>
> It's very nice to see the blackfin active again.
>
> After I compiled the skyeye on the cygwin and tested with R0504, it
> stopped after outputting following message and cpu is going to 100%...
>
> I've checked with common output and found the next output would be
> network driver. If I want to debug with skyeye and would like to see
> where it go to infinite loop, could you please give me some
> suggestions and advice?
>
> Regards,
> Andy
>
> $ ./skyeye.exe -e linux-bf533
> arch: blackfin
> uart_mod:0, desc_in:, desc_out:
> begin init emulator()
> exec file "linux-bf533"'s format is elf32-little.
> load section .text: addr = 0x00001000  size = 0x000d8500.
> load section .init: addr = 0x000d9500  size = 0x0000d0a0.
> load section .text_l1: lma = 0x000e65a0 (vma = 0xffa00000)  size = 0x000000cc.
> not load section .data_l1: addr = 0xff800000  size = 0x00000000 .
> load section .data: addr = 0x000e666c  size = 0x0002c9e8.
> not load section .bss: addr = 0x00113060  size = 0x0000d4c4 .
> not load section .comment: addr = 0x00000000  size = 0x00003162 .
> load section .romfs: addr = 0x00120524  size = 0x00800000.
> start addr is set to 0x00001000 by exec file.
>  ↑Linux version 2.6.12.1-BFIN-2005R4 (root at sevens) (gcc version 3.4.4
> (Blackfin 05R4 20051205)) #1 Wed Jan 11 15:33:21 C
> ST 2006
> Blackfin support (C) 2004 Analog Devices, Inc.
> ADSP-BF533 Rev. 0.0
> Warning: Unsupported Chip Revision ADSP-BF533 Rev. 0.0 detected
> uClinux/BF533
> Blackfin uClinux support by blackfin.uclinux.org
> Processor Speed: 110 MHz core clock and 22 Mhz System Clock
> Board Memory: 128MB
> Memory map:
>   text = 0x001000-0x0d9500
>   data = 0x0e666c-0x113054
>   bss  = 0x113060-0x120524
>   rootfs = 0x7700000-0x7f00000
>   stack = 0x0e8000-0x0ea000
> Instruction Cache Enabled
> Data Cache Enabled (write-through)
> Hardware Trace Enabled
> Built 1 zonelists
> Kernel command line:
> Configuring Blackfin Priority Driven Interrupts
> PID hash table entries: 256 (order: 8, 4096 bytes)
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Physical pages: 3c00
> Memory available: 59648k/130150k RAM, (49k init code, 865k kernel
> code, 231k data, 69632k dma)
> Blackfin Scratchpad data SRAM: 4 KB
> Blackfin DATA_A SRAM: 16 KB
> Blackfin DATA_B SRAM: 16 KB
> Security Framework v1.0.0 initialized
> Capability LSM initialized
> Mount-cache hash table entries: 512
>
> _______________________________________________
> Skyeye-developer mailing list
> Skyeye-developer at lists.gro.clinux.org
> http://lists.gro.clinux.org/cgi-bin/mailman/listinfo/skyeye-developer
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: R0504_linux_config
Type: application/octet-stream
Size: 11671 bytes
Desc: not available
Url : http://lists.gro.clinux.org/pipermail/skyeye-developer/attachments/20070212/2cb45d17/R0504_linux_config-0001.obj
-------------- next part --------------
A non-text attachment was scrubbed...
Name: R0504_user_config
Type: application/octet-stream
Size: 16715 bytes
Desc: not available
Url : http://lists.gro.clinux.org/pipermail/skyeye-developer/attachments/20070212/2cb45d17/R0504_user_config-0001.obj